Qu-Bit Electronix Nebulæ V1.1 Tutorial Videos

Nebulæ Basics: One-Shot Mode Published on May 21, 2015

"This is a tutorial on the basic One-Shot Mode functions of the Qu-Bit Electronix Nebulæ Eurorack module. The Nebulæ in this video is running the latest Firmware V1.1.

Table of Contents
Introduction: 0:00
Number of Samples: 0:18
Entering One-Shot Mode: 0:27
Buttons: 0:43
Button Sample Banks: 1:00
Identifying Sample Banks: 1:13
Kill All Samples Button: 1:28
Gate Inputs: 1:37
Kill All Samples Gate Input: 1:49
Vari-Speed: 2:10
Gates - Not Triggers: 2:31"

Nebulæ Basics: Looping Mode

Published on May 21, 2015

Additional videos below.

"This is a tutorial on the basic Looping Mode functions of the Qu-Bit Electronix Nebulæ Eurorack module. The Nebulæ in this video is running the latest Firmware V1.1.

Table of Contents
Introduction: 0:00
File Types: 0:14
Audio Output: 0:41
Speed: 0:51
Pitch: 1:47
Glide: 2:13
Grain Mix: 2:45
Grain Size: 2:59
Grain Rate: 3:25
Random Pitch Deviation: 3:58
Asynchronous Grain Rate: 4:20
Loop Start: 4:57
Loop Size: 5:18
Drive: 5:51
Recall: 6:22
Freeze: 6:37
Next File: 6:58
MIDI: 7:30

Piano Sample: Zai Zhe"

Nebulæ Advanced Features

Published on May 21, 2015

"This is a tutorial on the advanced functions of the Qu-Bit Electronix Nebulæ Eurorack module. The Nebulæ in this video is running the latest Firmware V1.1.

Table of Contents
Introduction: 0:00
Edit Button: 0:06
Speed Scaling: 0:11
Pitch Scaling: 0:37
File Selection Order: 1:03
Granular Random Pitch Deviation: 1:58
Granular Asynchronous Grain Rate: 2:22
Loading New Audio Samples: 2:45
Alternate Instrument Overview: 3:16
Loading Alternate Instruments: 3:40
Switch Between Alternate Instruments: 4:18

Piano Sample: Zai Zhe"

Nebulæ Firmware V1.1: Installation

Published on May 21, 2015

"This video goes over the functionality and installation of the Firmware V1.1 update for the Qu-Bit Electronix Nebulæ.

Table of Contents
Introduction: 0:00
Features: 0:08
Firmware Identification: 0:20
Firmware Contents: 0:44
Installation: 0:52"

Nebulæ Firmware V1.1: DIY

Published on May 21, 2015

"This is a tutorial on how to burn and flash the Firmware V1.1 update for the Qu-Bit Electornix Nebulæ

UPDATE: When burning the SD card image, type the command sudo dd bs=4m if=Neb_1_1.img of=/dev/disk2

Table of Contents
Introduction: 0:00
Tools: 0:10
Arduino IDE: 0:27
MIDI Library: 0:53
Firmware Sketch: 1:28
Upload the Firmware Sketch: 1:44
Remove the Chip: 2:28
Disk Image: 2:36
Burn the Disk Image: 2:58
Unmount the SD Card: 4:07
Remove the SD Card: 5:00
Congratulations!: 5:04

Websites Used:
Arduino IDE: http://arduino.cc/en/Main/Software
MIDI Library: http://playground.arduino.cc/Main/MID...
Library Info: http://arduino.cc/en/Guide/Libraries
Source Code: http://www.qubitelectronix.com/#!nebu..."