Steam Vent - #Eurorack Jamsessions ( #Electronica )

Published on Sep 2, 2016 Colin Benders

"After a month of truly bizarre events I finally found myself in one room with my modular again. Really needed to clear my mind so I went straight into track building mode. 1 hour in, this was the first result of the day. -- Watch live at https://www.twitch.tv/colinbenders"

Gieskes VCCDM1

Published on Sep 2, 2016 ggijs

via Gieskes

Part2 How to wire a Serge

Published on Sep 2, 2016 Dmitri SFC

"https://dmitribuildssynths.wordpress...."

Part 1 here.

SUSHI - Futomaki in development

Published on Sep 1, 2016 tatsuya shinyagaito

"Osc + Filter + LowPassGate module for Eurorack Synth"

Yamaha Montage Demo

Published on Sep 1, 2016 Xephyron Digital

"This is just a little recording I made while exploring the Montage"

Yamaha Montage Super Knob Demo

Published on Sep 1, 2016 Xephyron Digital

"This video demonstrates the complexity of the super knob and motion synthesis"

Patch Notes #17 - Reaktor Blocks As Eurorack Sequencer

Published on Sep 1, 2016 Voltage Control Lab

"Patch Notes #17 explores the Reaktor Blocks patch that we created in our previous tutorial, sending sequences via MIDI to the Make Noise 0-Coast, and triggers to 3 different Eurorack Drums.

Our Reaktor Blocks patch is running an 6 step sequence in pendulum mode out via MIDI to Mutable Instruments Yarns. Yarns channel 1 CV and gate outputs are routed to the the Make Noise 0-Coast pitch and gate inputs. The Korg SQ-1 is in random mode with a 2 volt range, sending one CV channel out to the voltage math section on the 0-Coast. One mult out from the voltage math section to the FM input on the oscillator, and one to the overtone section. A clock from the Make Noise Tempi is routed to the tempo input, and the stepped random out is routed to the decay length of the contour section. Out to the Malekko Mix4.

Roland System 1m is playing the pads/bass. A channel on Tempi sent into a mult, then on to clock Brains and Pressure Points, one channel of which is routed to the System-1m. The multed clock is also routed to the gate input on the System-1m. Internal LFO on the 1m is modulating the pulse width on the two slightly detuned square waves, long envelopes on the low pass filter and amp, and drenched in reverb and delay.

Reaktor Blocks is also generating 6 clock divisions from an internal clock divider, which is routed to the Gates & Trigs module. This device converts the gates from the clock divider to triggers, which are then individually routed out to 3 drum modules and Tempi. One rhythm is routed to the Noise Engineering Basimilus Iteritas, which is creating the glitchy, metallic snares. The BI clock source is multed to Make Noise Maths as well, channel 1 of which is routed out from both the unity and variable outputs to the morph and fold functions on the BI. Another Tempi channel is routed to the Make Noise Wogglebug as well, which is randomizing the BI pitch.

The kick and hihat are coming from the Scooper, in the Aira modular drum machine configuration we've covered about a year ago. The hihat length is randomized by the SQ-1 channel B. All modules are routed back through the Mix4, and on to the ping pong delay in Mutable Instruments Warps in Parasite mode.

https://www.voltagecontrollab.com/"

Moog Memorymoog Plus SN 3263

Note: links to listings are affiliate links for which the site may be compensated.

via this auction

"Upgrades-
- clean entire unit (including keyboard, switches, pots and knobs, plugs, and sockets)
- clean all board interconnects
- recap and reflow contour/glide PCB
- tested boards - all OK
- replaced chips on voice 1
- replaced chips on contour/glide board
- recap and reflow digital board
- installed new power supply with mods to digital and demux PCBs
- recap and repopulate demux PCB
- recap and repopulate common analog PCB
- test system - OK
- recap and repopulate all 6 voice cards
- test all voices - all OK
- replace battery
- resolved VCF control issue
- replace all OP amps on demux PCB
- replace capacitors and IC's
- install replacement OSC3 tuning control
- restore factory presets
- calibration
- final test - OK"

CLICK FOR MORE »

Moog Voyager XL

Note: links to listings are affiliate links for which the site may be compensated.

via this auction

CLICK FOR MORE »

Teisco 110F Synthesizer w/ Midi

Note: links to listings are affiliate links for which the site may be compensated.

via this auction

"Up for sale is the rare and amazing Teisco 110F. It's a duophonic synth similar to the Arp Odyssey and has PPC similar to the Odyssey but is a very different beast indeed. It has a great sounding 24db filter and an additional filter bank that you can route through as you wish percentage wise. There are leds giving you feedback as the audio passes and modulations occur in each stage of the audio path, very amazing. With cv connectivity it's great to use with a modular or an analog sequencer. Everything works great including the added midi kit*(more info below). There are a few blemishes on the end caps but otherwise this is very clean. The PPC does take some force to use but is perfectly normal, I keep it on the most sensitive setting on the sensitivity knobs so i don't have to strain as much. It's very reliable and the oscillators are stable over many octaves, you'll love this synth. It will be packed very carefully and double boxed so you can be sure it will get to you safely. Any q's just ask.

*MIDI to CV-Gate Interface MCV-628 by Papareil Synth Labs. The interface lets you control notes and one selectable control (either Filter Cutoff, PWM1 or PWM2). The button is an auto learn button to learn the midi channel of the incomming midi messages. The switch is to choose if either the notes will be triggered by the keyboard or the incoming midi. The knob has 4 positions and decide which parameter will be affected by modulation message (cc1): 1-cutoff, 2-PWM1, 3-PWM2, 4-OFF. The LED is a multi purpose led which blinks 3 times at power on, after the complete init of the cpu/software. It means "All is ok". In normal working condition, the Gate led lights when a note is played or if a recognised SysEx message is received. […] When the interface is in Autolearn mode, the Gate led stay on, until a MIDI message has been received."

CLICK FOR MORE »