Soundsdivine's Aalto Factory Presets.mov

YouTube via SoundsDivine111 | September 25, 2010

"Preview of the Soundsdivine presets for Madronalabs' Aalto synthesizer"

Teenage Engineering OP-1: We just bought a cheap oscilloscope on Blocket

YouTube via teenageengineering | September 25, 2010

"Looking at waveforms on this new oscilloscope. Testing different OP-1 Synth engines in the following order: Dr. Wave, FM, Phase, Digital. Enjoy! (sorry for the bad cam-quality and sound, as always...)"

ARP 2600C aka Grey Meanie with ARP Sequencer

YouTube via jobenbelgium | September 25, 2010

"The good old ARP 2600c aka Grey Meanie with it's friend the ARP Sequencer.Note that i'm not a musician,so recorded only for fun."

Dallas Synth Meet

via Facebook

"Time: Sunday, October 24 · 1:00pm - 4:00pm
Location: Elegant Accents, 2003 108th Street, Suite 301, Grand Prairie, TX 75050
Created By: Brandon McWhorter
More Info: BRING HEADPHONES even if you're not bringing gear. If you are bringning gear, also bring stands, power strip & extention cord (my power outlets are spaced weird)"

Metasonix R54 as a filter

YouTube via tkecni | September 25, 2010
"Metasonix R54 filtering the Malekko Anti-Osc"

Metasonix R54 vs R51

tkecni | September 25, 2010

"bass sounds of the combo...."

Morgan Orange: pimps on a short bus

YouTube via pmanderson70 | September 25, 2010

"Yamaha RS7000: sequencing, rhythm and voices
Yamaha AN200: sound fx
Yamaha TX81Z: FM Brass
Yamaha MO6: electric piano
Akai Miniak: lead voice
Behringer BCR2000: Sysex Controller for AN200"

Vintage Roland G-33 and GR-33B bass synth combo

via this auction

CLICK FOR MORE »

Custom Oberheim SEM MS1A Modular

via this auction

"custom Oberheim SEM MS1A Modular. The Modules themselves work fine but this is an AS-IS auction. Either you can either go over the patch wiring or you can toss the box, use the circuitry for your own Oberheim project, OR add a reiusse to the combo and you will have yourself a keyboardless TVS! I designed the front panel in Illustrator, sent the CAD file to a laser cutting facility on 3/16" black anodized aluminum with the added bonus etching the labels. One of the previous owners stripped the paint from the MS1A. The jacks are all 1/8" switchcraft. If you would like the name of a person who agreed to work on this I would be happy to supply that to the new owner, I just don't have the time pr patience for a project... even if I am not the one doing the work.

An excellent tech brought the SEM (also added a blue LED) and MS1A back to life and also recapped the power supply. The power supply is from a four voice unit. No buffering was added to the patch points since I just went by what was in the manual that came from SEM manual itself. The patch points were just brought to the front."

MOTM 1800 frac looping ADSR module

via this auction

"MOTM 1800 looping ADSR envelope. this module had banana jacks installed to replace the 1/8 jacks. the work was done by Michael Ford of Metalbox

the module generates a traditional adsr envelope at the 2 output jacks. when gate goes high (exceeds +2.5v), the attack/decay portion completes to the sustain level. the envelope stays at the sustain level until the gate signal goes low, then it releases to 0v. the trigger signal is optional: if your midi-cv controller can output a trigger pulse (1ms-10ms nominal width), the envelope will re-attack/decay when a trigger pulse is present. pressing the red manual gate pushbutton will also start the adsr cycle. the motm-1800 has 2 other modes: looping and burst. in the loop mode, the module acts like a lfo: the ads cycle repeats forever. note that the release control has no effect in the looping mode. for maximum output voltage swing in this mode, set sustain to the '0' tick. the fastest the loop will run is when attack and decay are both 0 and sustain is at 0 (looping will stop if sustain is set over the '6' tick). this will be about 620hz. if looping does not begin when you flip the switch, press and release the manual gate. in burst mode, the envelope will loop as long as gate is high. when gate goes low, the looping stops and the envelope does a release at the rate set by the release control. you can also burst with the manual gate pushbutton."

Modcan mix/lag 18a module

via this auction

"The MIX/LAG 18A is a 2 section module.
The top section is a 3 X 1 mixer for simple mixing of
voltages or audio

Features:
Inverting and non-inverting
attenuators for each of the 3 inputs
Offset control to add or subtract from the final mix

The lower section is a dual Voltage Controlled LAG processor. Lag is also known as glide, slew or portomento.
The primary use for lag is to smooth stepped voltage modulation input from a sequencer or midi to cv converter. The most common patch would be add glide to an oscillators pitch.

Features:

Manual and voltage control of lag time
Stable tracking and low drift
more info here:
http://www.modcan.com/modhtml/mix.html"